Auditd reconfigure using SIGHUP

Greetings, I was trying to reconfigure the Audit using SIGHUP and came across with below behavior of Audit. The audit version I am using is 2.3.6. Scenario 1: Starting auditd with active audispd plugin. 1. Activate the audispd plugin by setting active = yes in configuration file (example: /etc/audisp/plugins.d/syslog.conf) 2. Start the Auditd. Starting auditd will create the both Auditd and Audispd process. 3. Deactivate the audispd plugin by setting active = no in configuration file. 4. Reconfigure the Auditd by sending SIGHUP to Auditd (>> kill -SIGHUP <auditd_pid>). This reconfiguration stops the audispd process. 5. Activate the audispd plugin by setting active = yes in configuration file. 6. Reconfigure the Auditd by sending SIGHUP to Auditd. This should start the audispd process, however audispd process will not be started in this reconfiguration. Scenario2: Starting auditd with no active audispd plugin. 1. Start the Auditd. Starting auditd will create the only Auditd process. 2. Activate the audispd plugin by setting active = yes in configuration file. 3. Reconfigure the Auditd by sending SIGHUP to Auditd. This should start the audispd process, however in few cases audispd process will not be started in this reconfiguration. 4. Deactivate the audispd plugin by setting active = no in configuration file. 5. Reconfigure the Auditd by sending SIGHUP to Auditd. This reconfiguration stops the audispd process. 6. Activate the audispd plugin by setting active = yes in configuration file. 7. Reconfigure the Auditd by sending SIGHUP to Auditd. This should start the audispd process, however audispd process will not be started in this reconfiguration. As per the change log of audit version 2.3.2, below fix was made. Fix: In auditd, restart dispatcher on SIGHUP if it had previously exited I have analyzed Auditd code of version 2.3.6 and below is my observation. When the Auditd is started, it calls init_dispatcher() to start the Audispd. init_dispatcher() starts the Audispd and maintains its pid value in a global variable (auditd-dispatch.c). When the audispd is terminated, SIGCHLD handler of Auditd i.e child_handler() does the waitpid() to remove the child process from zombie state and calls dispatcher_reaped(), where this pid is set to zero. During reconfigure using SIGHUP, reconfigure_dispatcher() checks for this pid value. If pid is valid then, SIGHUP is sent to audispd otherwise init_dispatcher() is called to start the audispd. Auditd uses event loop ev_signal to track the child process (SIGCHLD). The event loop from libev also has child handler childcb() (in ev.c). This handler childcb() also does the waitpid(). When audispd terminates, libev's child handler is getting called first, waitpid() removes the audispd from zombie state. Then the control is passed to Auditd's child handler child_handler(). Since the audispd has been already removed from process stable, waitpid() call done in child_handler() will return ECHILD. Hence the dispatcher_reaped() is not getting called to make the internally maintained pid variable to zero. This results in subsequent SIGHUP set to Auditd end up in sending SIGHUP to non-existing audispd process. In case of step 3 of scenario 2: When the auditd is started without any active audispd plugin(step1), Auditd starts the audispd. However since there are no active plugins Audispd will get terminated. In this case shutdown_dispatcher() was called from dispatch_event() where pid value was set to zero. Hence the reconfiguration in step 3 started audispd process in my case. I have put traces in auditd code to validate the above behavior. This behavior is applicable for Audit version 2.6.4 as well. Is this behavior a known issue? Regards, Ketan